We seek to understand and document all radio transmissions, legal and otherwise, as part of the radio listening hobby. We do not encourage any radio operations contrary to regulations. Always consult with the appropriate authorities if you have questions concerning what is permissible in your locale.

Author Topic: Coax to use  (Read 1804 times)

Offline dss56

  • Newbie
  • *
  • Posts: 3
    • View Profile
Coax to use
« on: August 03, 2022, 0138 UTC »
Hi all hope this is the correct place to ask this question.

Getting ready to start an FM 88.5 radio station.

I built an adjustable dipole that will do 108-87mhz with easy tuning.

My question is what coax should i use. I knowrg213 is good but expensive 100ft it like $200+.

Can I use rg6 or some good small coax?
Transmitter is 25 watts adjustable and hope to use only 15 watts or less to cover a 2 mile radius.
Any suggestions on some small good coax/

thanks

Offline ~SIGINT~

  • DXing Phenomena
  • *******
  • Posts: 4103
  • N.E. Canada (FN08)
  • .ılılı..ılılı..ılılı..ılılı..ılılı..ılılı.
    • View Profile
    • Milspec Communication Canada
Re: Coax to use
« Reply #1 on: August 03, 2022, 0307 UTC »
With the output power you are running, your determinating factor will be more based along the length of coax between the transmitter and the antenna. Coax has a loss factor which is measured in dB per 100 feet at various standard frequencies. Although RG6 may be tempting, it is 75 Ohm coax vice 50 Ohm coax. Your transmitter and antenna will have a 50 or 52 Ohm impedance therefor you will need to match the transmission line to suite the equipment.

Some choices for common coax (with rounded figures):
RG-58 - 5dB of loss at 100 MHz;
RG-8X - 3.4dB of loss at 150 MHz; and
RG-213 - 2.1dB of loss at 100 MHz.

If you can pick-up some used LMR cable, that would be the best choice.
LMR-240 - 3.0dB of loss at 150 MHz (this is the size of RG-58); and
LMR-400 - 1.5dB of loss at 150 MHz (this is the size of RG-213/RG-214).

dB Conversions:
 1dB loss means about 21% of the signal is lost;
 2dB loss means about 37.5% of the signal is lost;
 3dB loss means 50% (half) the signal is lost;
 6dB loss means 75% of the signal is lost; and
10dB loss means 90% of the signal is lost.

Hope this helps somewhat in making the right choice.

Offline redhat

  • DX Legend
  • ******
  • Posts: 1585
  • USA
  • Music is my drug.
    • View Profile
    • Email
Re: Coax to use
« Reply #2 on: August 03, 2022, 0653 UTC »
Agreed.  For runs under 50 feet, lmr240 is fine.  I use it for short cellular jumpers without issue.  Anything longer though, I'd use lmr400.

+-RH
Somewhere under the stars...
Airspy HF+, MLA-30/Mini-whip/Chi-Town Loop
Please send QSL's and reception reports to xfmshortwave [at] proton [d0t] me

Offline dss56

  • Newbie
  • *
  • Posts: 3
    • View Profile
Re: Coax to use
« Reply #3 on: August 03, 2022, 1435 UTC »
With the output power you are running, your determinating factor will be more based along the length of coax between the transmitter and the antenna. Coax has a loss factor which is measured in dB per 100 feet at various standard frequencies. Although RG6 may be tempting, it is 75 Ohm coax vice 50 Ohm coax. Your transmitter and antenna will have a 50 or 52 Ohm impedance therefor you will need to match the transmission line to suite the equipment.

Some choices for common coax (with rounded figures):
RG-58 - 5dB of loss at 100 MHz;
RG-8X - 3.4dB of loss at 150 MHz; and
RG-213 - 2.1dB of loss at 100 MHz.



If you can pick-up some used LMR cable, that would be the best choice.
LMR-240 - 3.0dB of loss at 150 MHz (this is the size of RG-58); and
LMR-400 - 1.5dB of loss at 150 MHz (this is the size of RG-213/RG-214).

dB Conversions:
 1dB loss means about 21% of the signal is lost;
 2dB loss means about 37.5% of the signal is lost;
 3dB loss means 50% (half) the signal is lost;
 6dB loss means 75% of the signal is lost; and
10dB loss means 90% of the signal is lost.

Hope this helps somewhat in making the right choice.

Offline dss56

  • Newbie
  • *
  • Posts: 3
    • View Profile
Re: Coax to use
« Reply #4 on: August 03, 2022, 1437 UTC »
Looks like my best choice will be the rg213
thanks for all the helpful info on the coax.

thanks to all who replied.

Offline ~SIGINT~

  • DXing Phenomena
  • *******
  • Posts: 4103
  • N.E. Canada (FN08)
  • .ılılı..ılılı..ılılı..ılılı..ılılı..ılılı.
    • View Profile
    • Milspec Communication Canada
Re: Coax to use
« Reply #5 on: August 03, 2022, 2035 UTC »
To be honest, if you look around eBay you can find some new, pre-terminated (with connectors) LMR-400 at pretty much the same price as RG-213. Keep in mind that true LMR is manufactured by TIMES MICROWAVE. Anything else is a knock-off.

Offline redhat

  • DX Legend
  • ******
  • Posts: 1585
  • USA
  • Music is my drug.
    • View Profile
    • Email
Re: Coax to use
« Reply #6 on: August 06, 2022, 0613 UTC »
I've used the off brand lmr cable with good results.  I've been using off brand half inch super flex on projects lately also without incident.

+-RH
Somewhere under the stars...
Airspy HF+, MLA-30/Mini-whip/Chi-Town Loop
Please send QSL's and reception reports to xfmshortwave [at] proton [d0t] me

Offline M R I

  • Full Member
  • ***
  • Posts: 216
    • View Profile
Re: Coax to use
« Reply #7 on: August 06, 2022, 1625 UTC »
I have used LMR cable in the past. The newer cheaper brand cables are working just as good.
Mix.Radio.International [at] ProtonMail [dot] com