We seek to understand and document all radio transmissions, legal and otherwise, as part of the radio listening hobby. We do not encourage any radio operations contrary to regulations. Always consult with the appropriate authorities if you have questions concerning what is permissible in your locale.

Author Topic: Loop balun ratio?  (Read 1837 times)

Offline Capt. Kidd

  • Jr. Member
  • **
  • Posts: 37
    • View Profile
Loop balun ratio?
« on: March 27, 2018, 2310 UTC »
Lately I’ve decided to try to rebuild my shortwave station and do to space restraints I’ve had to build a loop antenna, I’ve had the thing for a while now it’s 150 feet of number 16 wire on a 5 foot pvc frame hoisted 20 feet in the air. The balun I have is 9:1 and I used it because it’s what I had. I’ve been told to use everything from 1:1 to 12:1. And ideas?
Broadcasting from nowhere in particular
QSLs accepted at
Ghostshiplive(at)gmail(dot)com

Offline ThaDood

  • DX Legend
  • ******
  • Posts: 1209
  • Likely, not where you are.
    • View Profile
    • Extreme Part #15!
    • Email
Re: Loop balun ratio?
« Reply #1 on: March 29, 2018, 0233 UTC »
Gee, you are pretty ambitious for a Kidd. Um... I've always done well with 4:1 W2DU current baluns. When you do your windings, don't put them too close together, or else that antenna will just RX FREQ's 5MHz and below, and little above that. Use the FREQ's of WWV, CHU, and 6070kHz CFRX (Since it's on-air 24/7.), to test RX with. Try the 9:1 balun, then try again without it. Good luck and Happy DX'ing!!!!!
I was asked, yet another weird question, of how I would like to be buried, when I finally bite the big one. The answer was actually pretty easy. Face-down, like a certain historical figure in the late 1980's, (I will not mention who, but some of you will get it, and that's enough.) Why??? It would be a burial that will satisfy everyone: (1) My enemies will say that it will show me where to go. (2) On the same point, I can have my enemies kiss my butt. (3) It will temporarily give someone a place to park a bicycle. See??? A WIN / WIN for everyone.

Offline RobRich

  • DX Legend
  • ******
  • Posts: 1722
  • Tampa, FL USA
    • View Profile
Re: Loop balun ratio?
« Reply #2 on: March 29, 2018, 2013 UTC »
Loop design? For example, 5' circumference circle? 5' sides on a square loop?

Are you transmitting? If so, you probably are going to need to rethink the small loop concept. The type of loop you should look into is a magnetic loop. The big issue there is the need for a high-voltage variable capacitor if moving around frequencies. Something like 30 to like 230pF variable capacitor rated at a few thousand volts with a ~1/10-wavelength (at lowest frequency) secondary loop and a primary feed loop at 1/5 the secondary loop size. Feed the primary with coax, and resonant the secondary with the capacitor. There are lots of design plans on the net for research.

Are you just receiving? You could use what you have, or just a copper pipe loop of a few feet in circumference for that matter, and forget the balun IMO. Instead use a small preamp at the loop feedpoint to deal with the impedance variances and wideband gain design concerns. Instead of a balun you might consider some ferrites or a toroid on the feedline if really desired, though a well-balanced loop usually tends to be rather resistant to feedline common mode anyway.
Tampa, FL USA | US Map Grid EL88
Airspy HF+ Discovery | KiwiSDR 2 | 2x Msi2500 Msi001 | 2x RTL-SDR V3 + NE602 | 2x RTL-SDR V4
148' Loop-on-Ground | 31' Vertical | 18' End-Fed Vertical | 9' NCPL | PA0NHC MiniWhip