We seek to understand and document all radio transmissions, legal and otherwise, as part of the radio listening hobby. We do not encourage any radio operations contrary to regulations. Always consult with the appropriate authorities if you have questions concerning what is permissible in your locale.

Author Topic: Best broadband receiving antenna below 500khz (longwave, NDB, DGPS)  (Read 4949 times)

Offline Uli_Bel

  • Jr. Member
  • **
  • Posts: 61
    • View Profile
For reception of the NDB-Band, down to even 10kHz (Alpha beacons), I was searching for the best reception antenna.

I use broadband loops for shortwave (horizontally mounted on an insulated pipe, top of 1.5" /50mm fiberglas) - that works well. However the loops loose sensitivity quickly (also if mounted vertically), if frequency is lowered below the cut-off frequency.

So what I needed:
- directivity, at least down to 250kHz hopefully even lower in frequency
- high enough output of the system
- free of common-mode noise
- steerable in direction, or at least switchable in direction

I use 170m Beverages, but it is always a lot of maintainance involved to keep everything perfectly working. According to Murphy, problems with the wires occur, when weather is terrible, the fields are in deep mud, and temperature is just above the freezing point.... you know what I mean...

So in the meantime I am testing the following:
- Small fiberpoles with attached vertical dipoles, 2x2.5m and a push-pull, high impedance amplifier and feedcable driver in the middle of the vertical dipol
- homebrew phasing network to phase and adjust the output of several vertical dipoles in the shack
- Large spacing between the vertical dipoles (100m = 0.1 x wavelength on 300khz)

If you think, that verticals are noisy, try two of them phased for optimum pattern - you will be astonished, how much better signal to noise ratio can be. The improvement over a single vertical is just incredible.

I regular post my overnight reception results in de DGPS portion of this forum

Several tests still to be done:
- Is it possible to change the vertical dipoles into just groundplanes without getting too much troubles of common-mode noise ?
- I also used a large EWE (20m x 60m x 20m) on 300kHz with great result. However this beast is really large - not easy to install it in many different directions. Also such EWE antenna is just the same as two verticals with the horizontal topwire being the phasing line. However I like to know, what is the smallest EWE, which has still enough output on 300kHz, if you do NOT use any pre-amp and just use passive broadband matiching with matching transformer... I think the efficiency must be in the area of -30dbi, hopefully better. I guess, that a 300kHz EWE cannot be much smaller than what I used recently (20x60x20m). At least you have to have the two vertical parts at a large spacing - otherwise it will become difficult to achieve any directivity without a large signal drop...

I will post my findings here for the community...

If you have any further suggestion, let us know ...

Ulli, ON5KQ
my online web-receiver, during the winter set-up with Beverages, daytime with horizontal loops at 11m

Offline IQ_imbalance

  • Sr. Member
  • ****
  • Posts: 345
  • Central MD
    • View Profile
Re: Best broadband receiving antenna below 500khz (longwave, NDB, DGPS)
« Reply #1 on: February 21, 2018, 1452 UTC »
I had pretty good luck with NDBs using my H-800...but that was with my PCR-1000, not the Afedri (which is sensitive to BCB overload).  Might be worth looking at LF Engineering's dedicated LF antennas, depending on your receiver.
LOG/NE-SW unterminated BOG/DJ-130/800Mhz Yagi
Central MD

Offline RobRich

  • DX Legend
  • ******
  • Posts: 1674
  • Tampa, FL USA
    • View Profile
I used to routinely listen to European longwave broadcasters using my 148' loop-on-ground antenna.


"Used to" because many of the LW broadcasters have shut down.
Tampa, FL USA | US Map Grid EL88
Airspy HF+ Discovery | 2x Msi2500 Msi001 | 2x RTL-SDR V3 + NE602 | 2x RTL-SDR V4
148' Loop-on-Ground | 31' Vertical | 18' End-Fed Vertical | PA0NHC MiniWhip

Offline ThElectriCat

  • Full Member
  • ***
  • Posts: 113
  • Hillsboro OR
    • View Profile
I haven't experimented much with active loops, but I am usually a fan of small (relative to wavelength) loops over wire antennas, even loops of the untuned vareity. I get a much higher noise floor on wire antennas, and switching to the loop does not lower the signals any more than it lowers the noise. That being said, I also have an ac powered receiver, and operate at my house. if you can get away from the city, the wire may preform better.  as far as active antennas go the best source of info I have ever found is this site
it is pretty much devoted to stuff below 22 kilocycles, but almost all of their "receivers" are actually preamplifiers, amplifying audio range rf signals. these designs could probably be scaled up to higher frequencies. whatever you do, if you build a preamp, make sure it has a good rolloff in gain above 500 kilocycles, or even weak AM stations will clip and intermodulate your front end
In another life, I could have been a telephone engineer.

Offline Looking-Glass

  • DX Legend
  • ******
  • Posts: 1133
  • Condobolin, NSW, Australia
  • "Old fashioned DXer, no offshore computer rxing!"
    • View Profile
Was told a couple or more years back by a Scottish SWLer that Wellbrook Loops from the UK are the way to go for LW DXing, not cheap in price but very efficient... ;D
« Last Edit: April 08, 2018, 2304 UTC by Looking-Glass »
Condobolin, NSW.

Grid Square:  QF37ub

Yaesu FT-1000D, Yaesu FT-2000D, ICOM IC-736 HF/50MHz, ICOM IC R75 & Tecsun S-2000 to 450 feet of wire, 27MHz 1/2 wave CB antenna converted to 21MHz & a multi band vertical of dubious reliability.

Offline ThaDood

  • DX Legend
  • ******
  • Posts: 1195
  • Likely, not where you are.
    • View Profile
    • Extreme Part #15!
    • Email
         I've been wanting to try the WOG (Wire On the Ground.) A friend of mine swears by it, and having it on the ground reduces the QRM noise levels. just don't lay it out where you have buried power lines, or under the power lines above. Unfortunately, being April 2018, we are now getting into constant lightning static noise season, but this November I know that I'd like to give this a try and lay out about 200ft of EXT cord and use that as the WOG for the winter.
I was asked, yet another weird question, of how I would like to be buried, when I finally bite the big one. The answer was actually pretty easy. Face-down, like a certain historical figure in the late 1980's, (I will not mention who, but some of you will get it, and that's enough.) Why??? It would be a buial that will satify everyone: (1) My enemies will say that it will show me where to go. (2) On the same point, I can have my enemies kiss my butt. (3) It will temporarily give someone a place to park a bicycle. See??? A WIN / WIN for everyone.

Offline RobRich

  • DX Legend
  • ******
  • Posts: 1674
  • Tampa, FL USA
    • View Profile
I used to run an 150' grasswire built with RG-6 coax fed with RG-6 coax. Center of the feedline coax was to the center conductor of the antenna coax with the far end shorted back to shield. The shield side of the feedline coax can go to a ground rod, a couple of perpendicular shorteneed radials, etc. I did not bother with a transformer.

That said, using just wire for the primary antenna element should suffice as well. I just happened to have lots of RG-6 coax to use.

I did not check longwave performance at the time, but it worked fine for my purposes for MW BCB through much of the HF spectrum. I did have a preamp available, but I do not remember using it much, especially at lower frequencies.
Tampa, FL USA | US Map Grid EL88
Airspy HF+ Discovery | 2x Msi2500 Msi001 | 2x RTL-SDR V3 + NE602 | 2x RTL-SDR V4
148' Loop-on-Ground | 31' Vertical | 18' End-Fed Vertical | PA0NHC MiniWhip


Item image   Vintage Midland 13-801 3 Channel CB transceiver