We seek to understand and document all radio transmissions, legal and otherwise, as part of the radio listening hobby. We do not encourage any radio operations contrary to regulations. Always consult with the appropriate authorities if you have questions concerning what is permissible in your locale.

Author Topic: Shortened BOG Array  (Read 478 times)

Gr0undPlan3

  • Jr. Member
  • **
  • Posts: 91
Shortened BOG Array
« on: November 03, 2026, 0108 UTC »
In the past, I had a 180 feet low Beverage (~3 feet) terminated in 470 ohms facing about 340 degrees. Antenna wire was THHN stranded fed to a transformer to 75 Ohm coax. It was quiet and worked. But it was 'facing' North so somewhat limited. I was also using a crude vertical at the time.

Then I put up a proper multi-band quarter wave vertical. Still quiet and omni-directional. I could hear much more than the Beverage, including noise, especially in the lower bands. The Beverage and crude vertical came down at this point and I used only the quarter wave vertical.

I have gotten to the point where I would like some directivity, especially in the lower bands. I have a HOA lot, so towers are out of the question.
To keep it stealth, I'm going to try a 4-way BOG array, that will be far shorter than ideal. I’ve had decent results with 180 feet. And, this is a RX only array.

To implement all four directions, I need a little over 1,000 feet of coax. I currently have about 600 feet. The feedlines eat up much of the coax since there are two equal lines per feedpoint. My longest run will be for the E-W Beverage, 400 feet of feedline. I will start with the E-W leg since I have everything I need to start on hand.

Also, it may easy to test F/B using WWV to the West. I should see a signal decrease when listening to WWV on the East leg compared to the West leg. Maybe I’m wrong or my F/B will be terrible.



The lengths listed above are the total length of the coax. The feedline run measures to just over 200 feet (x2). Sections D, E and F will require connecting each section into the total 218 feet. Not certain how I will join those sections yet.

The reversible BOG is based on section 2.15.5 in ON4UN’s Low-Band DXing. Excellent book with an excellent section on receive-only antennas. The concept is based on using both the braid and center conductor as two separate wires. 2:4 transformers wound on binocular cores are used at each end to terminate either the center conductor, or the braid.

Since my ‘wires’ will be on the ground, ZSURGE is estimated to be 300 Ohms. I’m using 75 Ohm coax and my transformers (T1 and T3) are measuring between 305 and 308 Ohms.

The feedpoint contains both the feedpoint to the shack (2X) and the other 2:4 transformer for the antenna section. Gas discharge tubes (GDT) to ground rods are used at each end for lightening protection.



The end termination will go on the West leg and the feedpoint/termination will go on the East leg.



I’m currently getting rain at the QTH and I’m hoping to get the E-W leg installed externally this week. Much easier to pound ground stakes into soft ground. Not much rain recently and very dry.

I’ve also built an entrance panel with GDTs and braid-breaker transformers on each line. More on that to come as this progresses this week.

Thanks for looking.
« Last Edit: November 15, 2026, 2123 UTC by Gr0undPlan3 »
WA8185SWL || qrzcq.com || eQSL.cc
QTH: Westerville, Ohio

Gr0undPlan3

  • Jr. Member
  • **
  • Posts: 91
Re: Shortened BOG Array
« Reply #1 on: November 12, 2026, 1542 UTC »
UPDATE#1

ENTRANCE PANEL

The entrance panel is straight-forward.



Each coax/direction will feed through a GDT and then a 2:2 transformer to isolate common mode currents. There is a pair of double coax + ground that comes into the house for a total of 4 coax and 2 grounds. I’ll tie those outside grounds together and attach a ground rod for QTH ground. The inside grounds will attach to the entrance panel.

To check for losses through the entrance panel, I performed a 5 Vpp sweep from 600 Hz to 30 MHz with my SG and saw no loss and no spill-over to adjacent lines.



E-W Beverage – 255’

Physical length of the installed E-W Beverage is 255 feet and works surprisingly well.

Even in the AM broadcast band where the antenna is really short, I am able to null out a local AM station to the west of my QTH. 1270 AM WDLR 500 W. The N-S null is also strong with the major local stations to the south almost completely nulled. Did not specifically check yet, but under the assumption the clear channels in Cleveland and Detroit would be knocked down or nulled completely.



WWV is more difficult to null although there is a 3-5 S-meter drop listening to WWV on the east Beverage.

I appear to have mis-labelled the feed ports, east was actually west and west was east. Glad I waited to WX proof until after testing! Switched the feedlines to the correct ports and WX proofed them.

Due to tree roots, I was no able to get the feedpoint ground rod very deep. I’m going to add a second ground rod 5 or 10 feet away and bond it to the existing ground rod. I’ll bury the new one to ease mowing in the area when the time comes again next season.

E-W performance has surprised me, I did not expect much nulling considering the lack of space for a proper Beverage. Working on the N-S Beverage next.

WA8185SWL || qrzcq.com || eQSL.cc
QTH: Westerville, Ohio

ThaDood

  • DX Legend
  • ******
  • Posts: 1659
  • Likely, not where you are.
    • Extreme, Part #15!
    • Email
Re: Shortened BOG Array? Puts my W.O.G. to shame.
« Reply #2 on: November 15, 2026, 1841 UTC »
WOW!!!! Some time, $$$$, planning, and some damn good engineering, applied to that BOG project. Mine??? After listening to a friend coax me to try that, I´ve compromised to using an idea of a W.O.G., Windom On Ground. About a decade ago, A friend of mine asked if I wanted old, ripped-up, commercial RG-11 coax, like hundreds of feet of it. Price was right, so ´YEAH!!!´. Sure, the #10AWG center conductor is totally contaminated, but I didn´t care, for my application of use. That 1/2¨ solid aluminum shielding, with that heavy-duty PVC jacket, makes the perfect Grounding conductor & Low FREQ Antenna. So, I used about 250ft of that trashed RG-11 to home-brew my own W.O.G. Beverage Antenna System. So, a 40-some foot run of RG-mini-8 coax, goes to one of my W2DU 4:1 multi-toroid current Balun, the 200W version with grey PVC piping. (The key was to keep this away from the noises of the house & road power lines.) Then, have one 100ft leg hug the soil as a crescent-shape down hill to the valley floor, and away from the road power lines. The other 150ft leg hugs the shoulder of the hill, then goes 3/4-way down hill, to stay away from the garage, where my AM1620, 3 meter antenna, is transmitting. So, real rime, or reason, to the lengths here? Um, no... In-house, a quick disconnect pig-tail was made to plug IN / OUT the Beverage Antenna Inputs of whatever rig I use.  This pig-tail has a terminal strip of opposing 1N4148 diodes for spike, and severe RF, reduction. The results???? This is actually a better Medium Wave Antenna System, than the raised Windom. From like late February to maybe around Halloween, or later, the raised Windom gets an earful of lightning crashes from 40M, on down. (Even on 20M.) However, during Summer months, I can again listen to Medium Wave Broadcasts, listen to 160M HAM´s, 120M Broadcasts, WWV 2.500MHz, regional 75M / 80M HAM´s, regional 60M HAM, WWV 5.000MHz, 48M Broadcasts, and even regional 40M HAM´s and Broadcasts. Will it receive above that? Well, yes, but much, much, more attenuated signals. Anyway, Saturday nights, I can again listen to This Week In Music History on Philly´s 1210 WPHT on Saturday nights, and not get an earful of lightning crashes. (As much...) The lighting crashes are attenuated like -20dB, or more. On the 75M / 80M HAM Band, imagine having the quiet noise floor of 2M SSB, or even 432MHz SSB, for that low in FREQ! Yes... This W.O.G. is not a DX Champ of an antenna system, but it does allow me to hear something locally & regionally on these lower HF & MW bands. Now, LF, below 500kHz, I have lots of attenuation here. I fault this to the lower-end spec´s drop-off of the W2DU Balun. I can still just hear WWVB at 60kHz, but in the Winter, the raised Windom gets that from S+9 to S+20/9. Being Near-South, in SW West Virginia, I can routinely hear lightning crashes from Cuba, Mexico, & the Caribbean. So, my W.O.G. as effective as  Gr0undPlan3´s? No where near, but the fact that it is usable to me on those lower FREQ´s during the warm & hot season, made it a worthy project to me nonetheless.  Oh... One more thing, The W2DU Balun is grounded at the PL-259 Connector, which seemed to make a difference on RX sensitivity even more so, below 3MHz.  Do I have any photos of all this? Um, no... That´s kind of the idea as well, out of sight, out of mind, for the many that are non-RF conscience. Could, make for a nice H.O.A. hidden project??? Maybe... Anyway, all my take on this subject.   
The best two statements of advice that I've ever gotten are from my brother-in-law in the early 1990's. 1st one, when I bought a used '89 Olds Cutless, my bro-in-law said, "Congratulations!!! You've just bought a deficit!". The other, was on a work environment, " No matter where you go, it's going to be f***'ed -up!". No truer words have been spoken.

Gr0undPlan3

  • Jr. Member
  • **
  • Posts: 91
Re: Shortened BOG Array? Puts my W.O.G. to shame.
« Reply #3 on: November 16, 2026, 0057 UTC »
WOW!!!! Some time, $$$$, planning, and some damn good engineering, applied to that BOG project.   

Thanks for the compliment ThaDood! I have been researching and planning for about 3 months.

I've accumulated this stuff over the years and ON4UN's book really got me into an antenna building mood. So far, only had to pick up a 10-pack of F-connector barrels. Need to purchase coax for the N-S leg and Newark has 1000' spools for <$200. I wanted to see how well this worked before buying more coax.

I can get a little over 200' for the N-S leg and it would terminate close to the house, so feedlines will be a reasonable length on the N-S leg. Leaving plenty of coax for maybe a phased pair of E-W Beverages down the road.

So far, this is a 160/80/40/20 antenna. Sweet spot for the nulls seems to be 40M. I do have some issues with the E leg, maybe due to the poor grounding at that end and/or coupling to the power lines across the road. Planning to get a better ground down there this week.

Weird results in the AM broadcast band. At times, stations will come in stronger from the opposite direction. I wonder if I'm seeing the Beverage backfiring at times? Although the nulling of stations N and S on this band is still encouraging.
« Last Edit: November 16, 2026, 1712 UTC by Gr0undPlan3 »
WA8185SWL || qrzcq.com || eQSL.cc
QTH: Westerville, Ohio

Gr0undPlan3

  • Jr. Member
  • **
  • Posts: 91
Re: Shortened BOG Array
« Reply #4 on: November 16, 2026, 1740 UTC »
UPDATE #2

SPLICED FEEDLINE DETAIL
Splicing of the feedline was kept simple. I used F-connector barrels to join the sections together and then WX proofed them using 3M Temflex. Since I’ve read multiple accounts of F-connectors coming loose, especially with a freeze/thaw cycle, I used removeable thread lock on the F-connector threads to keep them tight all year long. In theory...

Thread lock was applied to the F-connector barrels and allowed to cure overnight.

Since Temflex is notorious for leaving a nasty residue when removed, I protected the splice with painters’ tape before proceeding with the Temflex.


Next was a wrap of Temflex with good margins on each end.


Then a second wrap in the opposite direction of the first one.


Temflex is not UV-resistant so a wrap with Super 88 will protect the Temflex from UV exposure.


I repeated this process for the remaining splices, checking for continuity as I went.

Once complete with the spliced feedline, I used TDR to make one last check on the lengths of the both the feedline coax and the antenna coax. The feedlines are Southwire quad shield with a VP = 80% and the antenna element is Stellar Labs dual shield with a VP = 84%. All 75 Ohms.

Feedline #1 (spliced):

I used the following formula to calculate distance based on the time for the reflection of the 500 kHz signal to return to the scope:

#   L = ΔT * C * VP
#   L = (546 ns / 2) * 0.9836 ft/ns * 0.80
#   L = 214’

Feedline #2:

#   L = ΔT * C * VP
#   L = (520 ns / 2) * 0.9836 ft/ns * 0.80
#   L = 205’

Antenna:

#   L = ΔT * C * VP
#   L = (624 ns / 2) * 0.9836 ft/ns * 0.84
#   L = 258’

Next update soon - testing and troubleshooting.
« Last Edit: November 16, 2026, 1750 UTC by Gr0undPlan3 »
WA8185SWL || qrzcq.com || eQSL.cc
QTH: Westerville, Ohio