We seek to understand and document all radio transmissions, legal and otherwise, as part of the radio listening hobby. We do not encourage any radio operations contrary to regulations. Always consult with the appropriate authorities if you have questions concerning what is permissible in your locale.

Author Topic: Hack RF One SDR  (Read 2561 times)

Offline ChrisSmolinski

  • Administrator
  • Marconi Class DXer
  • *****
  • Posts: 31106
  • Westminster, MD USA
    • View Profile
    • Black Cat Systems
Hack RF One SDR
« on: September 13, 2019, 1736 UTC »
I recently acquired a Hack RF One SDR. This SDR is somewhat unique in that it transmits as well as receives. It was designed primarily for use in the VHF and UHF bands, but I was interested in how it performed on the HF bands, possibly for use as as a QRP transmitter in the ham bands. So I decided to take some measurements...

The Hack RF One has an adjustable VGA gain of 0 dB to 47 dB, and an RF amplifier.

Measurements taken with a 50 ohm dummy load and a Rigol SD1052E scope measuring the RMS voltage and calculating the power.

With the VGA set to the maximum of 47 dB and the RF Amp off, I got the following power output values:
475 kHz: 0.027 mW
1.9 MHz: 0.15 mW
3.8 MHz: 0.23 mW
7.1 MHz: 0.26 mW
14.1 MHz: 0.22 mW
28.2 MHz: 0.27 mW

With the VGA set to the maximum of 47 dB and the RF Amp on, I got the following power output values:
475 kHz: 0.048 mW
1.9 MHz: 2.7 mW
3.8 MHz: 9.7 mW (distorted waveform, backing down to 45 dB gave 7.8 mW)
7.1 MHz: 24 mW  (distorted waveform, backing down to 45 dB gave 16.5 mW)
14.1 MHz: 26 mW
28.2 MHz: 22 mW

Next to see the effect of varying the VGA. Yes, it does vary the output power. No, not exactly as much as you would expect from theory.

At 7.1 MHz, with the RF Amp off, measuring the output into a 50 ohm load:
47 dB 111 mV  0.246 mW
37 dB 44 mV   0.039 mW
27 dB 28 mV  0.016 mW

With the RF Amp on:
45 dB 880 mV 15.5 mW
35 dB 308 mV 1.90 mW
25 dB 109 mV 0.24 mW
15 dB 42 mV 0.035 mW

As a side note, the build in oscillator is pretty... bad. Off frequency. I just took a measurement vs my GPS 10 MHz reference, off by 71.3 ppm. Ouch.   I have a high stability oscillator on the way.  You can drive it with a 10 MHz reference input, which could be an option down the road.
Chris Smolinski
Westminster, MD
eQSLs appreciated! csmolinski@blackcatsystems.com
netSDR / AFE822x / AirSpy HF+ / KiwiSDR / 900 ft Horz skyloop / 500 ft NE beverage / 250 ft V Beam / 58 ft T2FD / 120 ft T2FD / 400 ft south beverage / 43m, 20m, 10m  dipoles / Crossed Parallel Loop / Discone in a tree

Offline KaySeeks

  • DX Legend
  • ******
  • Posts: 1246
  • Quebec. Vive la différence.
    • View Profile
Re: Hack RF One SDR
« Reply #1 on: September 14, 2019, 0046 UTC »
Thanks for doing this. I have been curious about this rig.

Quote
Next to see the effect of varying the VGA. Yes, it does vary the output power. No, not exactly as much as you would expect from theory.

At 7.1 MHz, with the RF Amp off, measuring the output into a 50 ohm load:
47 dB 111 mV  0.246 mW
37 dB 44 mV   0.039 mW
27 dB 28 mV  0.016 mW

With the RF Amp on:
45 dB 880 mV 15.5 mW
35 dB 308 mV 1.90 mW
25 dB 109 mV 0.24 mW
15 dB 42 mV 0.035 mW

I think what you mean is "not exactly as much as you would expect from the specifications."

The specs are likely only typical values, not max/min values, so don't be surprised if things differ "a bit" . (Everyone has a different definition of "a bit".  ;)  )

Noticing that with the amp off, the step from 47 to 27 dB (20 dB) was measured as 11.9 dB and with the amp on, that step was 18 dB. With the amp on, the the full step you have here (45 to 15 dB = 30 dB) was measured as 26 dB.

One of the things that happens with VGAs is that crosstalk from input to output can confound step characterization. Here's a table of your steps with the amp on:

45 dB --> 9.1 dB step from 35 dB
35 dB --> 9.0 dB step from 25 dB
25 dB --> 8.4 dB step from 15 dB

The incremental steps above are actually fairly uniform (but not exactly 10 dB) so crosstalk may not be the issue.

However, it is interesting that the step was closer to expected with the amp on, rather than off. Is there a possibility that the 27 dB value with the amp off is wrong? Are you measuring the noise floor of your oscilloscope at that step setting?

Any interest in a harmonic output or a two-tone IP3 characterization of the TX output?  8) :)
« Last Edit: September 14, 2019, 0119 UTC by KaySeeks »
Just somebody with a radio, a computer and a pair of headphones...

 

HFUnderground T-Shirt
HFUnderground T-Shirt
by MitchellTimeDesigns